Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (301.90 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Optimization level option is correctly used
[ 3.00 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g and -fno-omit-frame-pointer
-g option gives access to debugging informations, such are source locations. -fno-omit-frame-pointer improve the accuracy of callchains found during the application profiling.
[ 3.00 / 3 ] Architecture specific option -march=native is used
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (98.02%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] CPU activity is good
CPU cores are active 98.64% of time
[ 4 / 4 ] Threads activity is good
On average, more than 98.64% of observed threads are actually active
[ 4 / 4 ] Affinity is good (99.18%)
Threads are not migrating to CPU cores: probably successfully pinned
[ 4 / 4 ] Loop profile is not flat
At least one loop coverage is greater than 4% (44.56%), representing an hotspot for the application
[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (98.02%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.00%) lower than cumulative innermost loop coverage (98.02%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 964 - bench | Execution Time: 44 % - Vectorization Ratio: 98.34 % - Vector Length Use: 44.94 % | |
| ►Data Access Issues | 59 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, SHUFFLE/PERM, BROADCAST) - Simplify data access and try to get stride 1 access. There are 53 issues (= instructions) costing 1 point each. | 53 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Inefficient Vectorization | 53 | |
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, SHUFFLE/PERM, BROADCAST) - Simplify data access and try to get stride 1 access. There are 53 issues (= instructions) costing 1 point each. | 53 |
| ►Loop 1239 - bench | Execution Time: 28 % - Vectorization Ratio: 100.00 % - Vector Length Use: 96.53 % | |
| ►Data Access Issues | 56 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ○ | [SA] Presence of special instructions executing on a single port (SHUFFLE/PERM, BROADCAST) - Simplify data access and try to get stride 1 access. There are 52 issues (= instructions) costing 1 point each. | 52 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Inefficient Vectorization | 52 | |
| ○ | [SA] Presence of special instructions executing on a single port (SHUFFLE/PERM, BROADCAST) - Simplify data access and try to get stride 1 access. There are 52 issues (= instructions) costing 1 point each. | 52 |
| ►Loop 1294 - bench | Execution Time: 24 % - Vectorization Ratio: 100.00 % - Vector Length Use: 96.20 % | |
| ►Data Access Issues | 28 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ○ | [SA] Presence of special instructions executing on a single port (SHUFFLE/PERM, BROADCAST) - Simplify data access and try to get stride 1 access. There are 24 issues (= instructions) costing 1 point each. | 24 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Inefficient Vectorization | 24 | |
| ○ | [SA] Presence of special instructions executing on a single port (SHUFFLE/PERM, BROADCAST) - Simplify data access and try to get stride 1 access. There are 24 issues (= instructions) costing 1 point each. | 24 |
| ►Loop 280 - bench | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 18 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 8 issues ( = data accesses) costing 2 point each. | 16 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 17 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 8 issues ( = data accesses) costing 2 point each. | 16 |
| ►Loop 247 - bench | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 3 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |